Crowns and bridges - Estetic Special

Estetic Special

self - curing acrylic resin for temporary crowns and bridges

for making crowns and bridges beyond of patient oral cavity,
its elasticity and durability render it suitable for extensive temporary bridges,
a wide range of shades (V and WIEDENT) makes it possible to obtain the colour that ideally imitates the natural colour of teeth,
meets the requirements of PN EN ISO 10477.

Technical data:

mixing ratio: powder/liquid by weight - 2:1,
dough time: 2-5 minutes,
working time: 3,5 minutes,
curing time: 10 minutes at 40-50°C, 2 bar,
fracture strength: min. 59,1 MPa,
water solubility: 2,6 μg/mm³,
water sorption: 23,8 μg/mm³.

Packaging:

Sets:

100 g powder (75 g dentin, 25 g enamel), 50 ml liquid:
V shades: A1, A2, A3, A4, B2, C2, D3
WIEDENT shades: A2, B3, G1, G2, N3, R1, R5,
100 g powder, 50 ml liquid in two sets:
V shades: (12,5 g dentin in A1, A2, A3, A4, B2, C2, D3 shades; 12,5 g enamel in A3 shade),
WIEDENT shades: (12,5 g dentin in A2, B3, G1, G2, N3, R1, R5 shades; 12,5 g enamel in G2 shade).

Individually:

50 ml liquid.

Application:

for making temporary crowns and bridges beyond of patient oral cavity.

Properties:

self-curing polymer,
its elasticity and durability render it suitable for extensive temporary bridges,
a wide range of shades (V and WIEDENT) makes it possible to obtain the colour that ideally imitates the natural colour of teeth,
meets the requirements of PN-EN ISO 10477 international standard.

Proportions for mixing:

Recommended weight proportions of powder and liquid are like 2:1

Direction for use and curing:
Pour an appropriate amount of the solvent into a vessel and gradually add powder up to complete saturation with the solvent. Stir for a few seconds - solution should have the consistency of thick cream. Cover the vessel tightly and keep under cover for 2 to 5 min (depending on the temperature of the environment). Higher temperatures accelerate and lower delay initial swelling. Check plasticity with a spatula - if we consider the acrylic mass to attain the highest plasticity level (just after the phase of "drawing thread") the material is ready for use. Apply the plastic mass on the surface of the model and form under gradually increased pressure in a polymerizing mould. Polymerize in water at 40-50°C under 2 bar pressure for about 10 minutes. After polymerization process, polish crowns and bridges according to commonly used methods.

The manufacturer recommends the following guidelines to be included in instructions for the patients::

crowns made up of ESTETIC SPECIAL should be cleaned with a toothbrush using toothpaste,
damaged crowns and bridges should be repaired only by a dental technician or a dentist.

Storage:
Keep in tightly-closed containers in well-ventilated rooms. Keep out of the reach of children.

Best before: 5 years from the date of production.

WARNING:
The liquid is inflammable and also irritant. Avoid inhaling the vapours and prevent any contact with the skin and eyes. In case of contact, rinse thoroughly with water and, if any, contact your ophthalmologist. Don't dispose of the remainder of the liquid into the sewer. Dental technicians are warned against inhaling dust while carrying out prosthesis work. When engaged in this work, using of a dust-mask and a fume cupboard is recommended.

Instruction
Instructions for use of ESTETIC SPECIAL
Declaration of Conformity
Declaration of Conformity ESTETIC SPECIAL
Order form
Auxiliary products
Safety Data Sheets
SDS_Est S_Est Spec_powder
SDS_Est S_Est Spec_liquid
Catalogue page
Estetic Specjal

Estetic Special

Useful Links

Contact